Aluminum billet tour pack rack for HD tour packs.
Available in chrome or gloss black anodized.
Made in the USA from T-6061 Billet Aluminum. The pictures do not do it justice. It's absolutely beautiful!

Matching saddlebag racks available separately.

PROUDLY MADE IN THE USA!

Learn More

THESE CALIPERS THAT WE HAVE IN STOCK FIT ALL 2000-PRESENT HD TOURING MODELS W 13" BRAKE ROTORS. THESE ARE FOR FRONT SINGLE DISC APPLICATIONS ON THE LEFT SIDE.

We have the CHROME 6-piston differential bore calipers for 13" rotor applications IN STOCK and ready to ship. These calipers are engineered for maximum braking performance and show quality looks. They have no ugly company logos machined into them so they are smooth and beautiful, and they come with dual stainless steel bleeders standard.
They are manufactured from 6061 billet aluminum which provides a stronger more rigid caliper with less weight as compared to stock and some competitors cast calipers. These differential bore calipers utilize a smaller diameter piston at the lead-in of the rotor and a larger piston on the trailing side providing optimum friction dynamics by equalizing the heat distribution throughout the brake pad to rotor interface. HHI also employs dual piston seals providing each piston with 2 layers of protection from contamination promoting long term leak proof operation. In addition, this sealing system improves piston pullback which reduces brake pad drag on the rotor.

Further improvements have been made with specially designed permanent brake pad retainers providing quiet operation and an upgraded friction material promoting longer life and less pad dust. All calipers come complete with brake pads, mounting hardware, 10mm banjo bolt and crush washers for easy installation. HHI calipers are also compatible with DOT 4 or DOT 5 brake fluid.

***THESE CALIPERS THAT WE HAVE IN STOCK FIT ALL 2000-PRESENT HD TOURING MODELS W 13" BRAKE ROTORS. THESE ARE FOR FRONT SINGLE DISC APPLICATIONS ON THE LEFT SIDE.


MADE WITH PRIDE IN THE USA!!!

Learn More

These American made oversize 19" long drivers floorboards look cool, offer more foot placement choices, and actually increase lean angle when cornering. We STOCK these in a chrome or gloss black powder-coated finish WITHOUT rivets. We can also get them with rivets pretty quick. These boards are constructed of billet aluminum with a vibration absorbing rubber insert. These boards will bolt on directly in place of your stock boards on 1980 - present HD touring models and 1986 - present Softail models originally equipped with floorboards.

We prefer to use the rivet-less style Banana boards with the PM shift and brake arms, and PM rubber pegs which we offer elsewhere on this site. (The pattern on the rubber insert of the Banana boards is almost a perfect match to the PM pegs and grips) This will give you that clean and simple, less is more style that people will notice. Check out the bikes in the pics to see what we mean.

If you choose the riveted style Banana boards, then Banana style riveted shift pegs, brake pedal pad, passenger floorboards, sport banana boards that mount with a standard foot-peg style male mount are also available if you prefer this style. See the menu below to add these optional items. These add-on items are also available without the rivets if you prefer the Banana accessories with your rivet-less Banana drivers boards. If you choose rivet-less drivers boards, you will get rivet-less accessories from the menus below. Riveted drivers boards would get riveted accessories.

Note* The Passenger floorboards are made to bolt to the stock HD floorboard housings. When they are in the up position, you will still see the original HD floorboard housing.

ALL OF THESE PARTS ARE MADE WITH PRIDE IN THE USA!

Learn More

*** THESE PIPES WILL BE DROP SHIPPED TO YOU AND THAT WILL USUALLY TAKE 1-2 WEEKS. PLEASE CALL IF YOU WOULD LIKE TO CHECK AVAILABILITY BEFORE ORDERING. 269-276-9200.

THESE ARE OUR FAVORITE MUFFLERS ON THE PLANET!
I know that's a pretty strong statement but here's why: They sound absolutely killer. They produce the DEEPEST sounding exhaust note we have ever heard. Similar to a BIG BLOCK 60's Corvette with side pipes. They get loud when your in the throttle yet are mellow at cruising speed so they won't drown out your stereo system. These 4.5" diameter mufflers have a perforated inner wrapped in fiberglass and an additional (non removable) louvered core baffle to provide just the right amount of back-pressure. The finish on these pipes is also top notch. Tig welded muffler bodies and beautifully machined tips in a variety of styles. (see other listings for different style tips) Available in either show chrome or a black ceramic finish.

***These particular mufflers have special extended tips installed. For a shorter tip style see our other listings.

MADE IN THE USA!!!



Learn More

THESE CALIPERS THAT WE HAVE IN STOCK FIT ALL 2000-PRESENT HD TOURING MODELS W 13" BRAKE ROTORS. THESE ARE FOR FRONT SINGLE DISC APPLICATIONS ON THE LEFT SIDE.

We have the BLACK 6-piston differential bore calipers for 13" rotor applications IN STOCK and ready to ship. These calipers are engineered for maximum braking performance and show quality looks. They have no ugly company logos machined into them so they are smooth and beautiful, and they come with dual stainless steel bleeders standard.
They are manufactured from 6061 billet aluminum which provides a stronger more rigid caliper with less weight as compared to stock and some competitors cast calipers. These differential bore calipers utilize a smaller diameter piston at the lead-in of the rotor and a larger piston on the trailing side providing optimum friction dynamics by equalizing the heat distribution throughout the brake pad to rotor interface. HHI also employs dual piston seals providing each piston with 2 layers of protection from contamination promoting long term leak proof operation. In addition, this sealing system improves piston pullback which reduces brake pad drag on the rotor.

Further improvements have been made with specially designed permanent brake pad retainers providing quiet operation and an upgraded friction material promoting longer life and less pad dust. All calipers come complete with brake pads, mounting hardware, 10mm banjo bolt and crush washers for easy installation. HHI calipers are also compatible with DOT 4 or DOT 5 brake fluid.

***THESE CALIPERS THAT WE HAVE IN STOCK FIT ALL 2000-PRESENT HD TOURING MODELS W 13" BRAKE ROTORS. THESE ARE FOR FRONT SINGLE DISC APPLICATIONS ON THE LEFT SIDE.


MADE WITH PRIDE IN THE USA!!!

Learn More

Performance Machine makes some of the finest parts in the motorcycle industry, and this beautiful brake arm is no exception! Sculpted from billet aluminum and then triple chrome plated, black anodized, or black anodized and contrast cut if you desire, this brake arm will add a touch of cool to an otherwise overlooked area on your bike. This contour brake arm comes with the rubber brake pedal pad shown. Fits 97-present HD touring models. See below for choices.

MADE WITH PRIDE IN THE USA!

Learn More

These Cyclesmith American made oversize 21" long XL drivers floorboards look cool, offer more foot placement choices, and actually increase lean angle when cornering. The extra 2" on these boards compared to the 19" bananas is all in the front of the board. Notice how the front of the board follows the same angle as the HD engine guard. These boards are constructed of billet aluminum with a vibration absorbing rubber insert. These boards will bolt on directly in place of your stock boards on 1980 - present HD touring models and 1986 - present Softail models originally equipped with floorboards. (Shorter 19" drivers Banana floorboards are also available in another listing on this site)

We prefer to use the rivet-less style Banana boards with the PM shift and brake arms, and PM rubber pegs which we offer elsewhere on this site. (The pattern on the rubber insert of the Banana boards is almost a perfect match to the PM pegs and grips) This will give you that clean and simple, less is more style that people will notice. Check out the bikes in the pics to see what we mean.


ALL OF THESE PARTS ARE MADE WITH PRIDE IN THE USA!

Learn More

WE HAVE ONE PAIR IN STOCK AT THIS SPECIAL CLEARANCE PRICE!

These billet aluminum Arlen Ness CHROME Deep Cut fork boots are 2" longer than a standard fork boot. These are for use with longer fork tubes or a 2" or longer fork cap insert that comes with some aftermarket triple trees like raked trees. These fit 2014-Present HD touring models.

Learn More

This AMERICAN MADE taillight module will make single or dual function lights work as running, turn, and brake lights. It is a direct plug in installation between the main harness and YOUR EXISTING rear fender harness. This unit also has a built in load equalizer that will not overheat like the cheap imported modules. This direct plug-in module fits:
All 1996 - 2009 HD touring models. 2010-2013 Road Kings and Ultra classics. ’96-’10 Softails (except ’08-’10 FXCW/C, ’10 FLSTSE), ’97-’10 Dynas (except ’09-’10 FXDB, ’10 FXDWG), ’99-’03 Sportsters. Wiring instructions included.

With this module you must re-use your stock rear fender harness or come up with your own wiring to go from this module to your taillights. If you use your existing rear fender harness you will simply connect your existing turn signal wires to your new taillights. (one power wire and one ground wire)
If you'd rather not deal with re-using your stock rear fender harness then order our tail module WITH the attached harness found in another listing. These other taillight modules come complete with license plate, left taillight and right taillight harnesses with 36" leads and quick disconnects for these same 96-09 and 2010-2013 touring models as well. See our other listing for these.


MADE WITH PRIDE IN THE USA!!!

Learn More

This AMERICAN MADE taillight module INCLUDES A 36" LONG REAR FENDER HARNESS to simplify your rear fender wiring. It will make single or dual function lights work as running, turn, and brake lights and also includes a 36" lead to power your license plate light. It is a direct plug in installation into the main wiring harness. This unit also has a built in load equalizer that will not overheat like the cheap imported modules.

This direct plug module fits:
All 1996 - 2009 HD touring models as well as 2010-13 Road Kings and Ultra classics. ’96-’10 Softails (except ’08-’10 FXCW/C, ’10 FLSTSE), ’97-’10 Dynas (except ’09-’10 FXDB, ’10 FXDWG), ’99-’03 Sportsters. Wiring instructions included.

***THIS MODULE WITH A HARNESS WILL PROVIDE ALL 3 FUNCTIONS TO ANY LIGHT YOU HOOK TO IT.
IF YOU PLAN TO RUN ANY ADDITIONAL DEDICATED BRAKE OR RUNNING LIGHTS THEN ORDER THE RUN, TURN, BRAKE MODULE WITHOUT THE HARNESS. THAT MODULE CAN ALSO POWER YOUR STOCK BRAKE AND RUNNING LIGHTS.

We also offer taillight modules for the same applications listed above but WITHOUT a rear fender harness for $50.00 less. You will have to re-use your stock rear fender harness with those modules. Taillight modules for 2010-2013 Street Glide and Road Glide models available as well. See our other listings for these. If you need a module for a CVO model please call the shop.


MADE WITH PRIDE IN THE USA!!!


Learn More

THESE ARE OUR FAVORITE MUFFLERS ON THE PLANET!
I know that's a pretty strong statement but here's why: They sound absolutely killer. They produce the DEEPEST sounding exhaust note we have ever heard. Similar to a BIG BLOCK 60's Corvette with side pipes. They get loud when your in the throttle yet are mellow at cruising speed so they won't drown out your stereo system. These 4.5" diameter mufflers have a perforated inner wrapped in fiberglass and an additional (non removable) louvered core baffle to provide just the right amount of back-pressure. The finish on these pipes is also top notch. Tig welded muffler bodies and beautifully machined tips in a variety of styles. (see other listings for different style tips) Available in either show chrome or a black ceramic finish. Please call the shop to check availability or if you have any other questions. 269-276-9200

***These particular mufflers are all chrome and have standard length TOTALLY SMOOTH tips.

***They will be drop shipped directly from the manufacturer.

MADE IN THE USA!!!

Learn More

For only a few bucks you can clean up the looks of your STOCK fork legs with this trick AMERICAN MADE flush front axle. This Native STAINLESS STEEL 25mm flush axle is available with chrome or gloss black ends for the 2008-present HD touring models. A installation tool is included along with instructions as well. Please choose your axle end cap finish from the menu below.

Learn More

***THESE SPACERS DO NOT FIT 2014 AND LATER TOURING MODELS***

If you have STOCK STYLE fork legs and a custom fender on your 1984-2013 HD touring model, then you have just found the ultimate fender spacer for your application. These fender spacers will work with most 16-30" fenders. Native Customs has designed these billet aluminum fender spacers to match the contour of the STOCK STYLE fender mounts perfectly. We offer these spacers in FOUR different widths and in your choice of show chrome, gloss black powdercoat, or in raw machined aluminum. All of these spacers have holes on 3.000" centers which is the same pattern as 1984-2013 HD touring models. We also make fender spacers for aftermarket billet style fork legs which can be found in another listing.

Please see the menus below for choices.

***SHIPPING IS ONLY $6. IF THE WEBSITE CHARGES YOU MORE WE WILL REFUND THE DIFFERENCE.

MADE WITH PRIDE IN MICHIGAN!!!



Learn More

THESE ARE OUR FAVORITE MUFFLERS ON THE PLANET!
I know that's a pretty strong statement but here's why: They sound absolutely killer. They produce the DEEPEST sounding exhaust note we have ever heard. Similar to a BIG BLOCK 60's Corvette with side pipes. They get loud when your in the throttle yet are mellow at cruising speed so they won't drown out your stereo system. These 4.5" diameter mufflers have a perforated inner wrapped in fiberglass and an additional (non removable) louvered core baffle to provide just the right amount of back-pressure. The finish on these pipes is also top notch. Tig welded muffler bodies and beautifully machined tips in a variety of styles. (see other listings for different style tips) Available in either show chrome or a black ceramic finish. Please call if you have any questions. 269-276-9200

***These particular mufflers are all chrome and have standard length tips with flutes on the inside and outside of the tip***

***They will be drop shipped from the manufacturer.

MADE IN THE USA!!!


Learn More

Performance Machine makes some of the finest parts in the motorcycle industry, and this beautiful shift arm is no exception!

These shift arms are about 1.25" longer than a stock HD shift arm. Sculpted from billet aluminum and then triple chrome plated, black anodized, or black anodized and contrast cut, this shift arm will add a touch of cool to an otherwise overlooked area on your bike. (the contrast cut version has the contrast silver areas polished to a high luster)
This shift arm comes with the contour shift peg (with rubber insert) and shaft spacer shown. Also available in a heel / toe version. Fits 84-present HD touring and 00-10 FLST models. See below for choices.

***These shift arms are NOT COMPATIBLE with 2014 and later WATER COOLED HD touring models***

***The heel shifter is also 1.25" longer that stock so these PM heel and toe shifter combos have 2.5" more room between the shift pegs***

MADE WITH PRIDE IN THE USA!

Learn More

***THESE SPACERS DO NOT FIT 2014 AND LATER TOURING MODELS***

If you have American Suspension or Arlen Ness billet fork legs and a custom fender on your 1984-2013 HD touring model, then you have just found the ultimate fender spacer for your application. These fender spacers will work with most 16-30" fenders. Native Customs has designed these billet aluminum fender spacers to match the contour of the Arlen Ness Hot Legs and the EARLY STYLE American Suspension bagger legs fender mounts perfectly. (These do not fit the late style American Suspension fork legs that use studs w nuts to attach the fender mount to the fork leg) You will have a even gap around the rectangular portion of the fender mount. We offer these spacers in FOUR different widths, and in your choice of show chrome, gloss black powdercoat, or in raw machined aluminum. All of these spacers have holes on 3.000" centers which is the same pattern as all 1984-2013 HD touring models. We also make fender spacers for stock style legs which can be found in another listing.

***SHIPPING IS ONLY $7. IF THE WEBSITE CHARGES YOU MORE WE WILL REFUND THE DIFFERENCE.

Please see the menus below for choices.

MADE WITH PRIDE IN MICHIGAN!!!


Learn More